Description and classification of the role of needle piercing
2 posters
Page 1 of 1
Description and classification of the role of needle piercing
When Piercing needle is a billet for brass forging
parts Extrusion bronze casting on sale
and to identify products within Brass forging the perforation hole size tool. Perforated
pipe inner surface of the needle in the quality assurance plays a decisive role. Needle
piercing the general circular cross-section for the production of pipe, pipe, and
gradually shaped cross section profiles. Piercing needle structure and brass forging
extrusion methods of operation and selection of product requirements.
Column part perforated cylindrical needle work, and its cross section round, shaped
and so on. Needle along the needle axis of column has a small taper, in the extrusion
process, the stationary perforated needle,sanitary
ware fittings only the front end with a tapered needle; and follower wearPin hole,
you need the entire length of the work of a very small taper to reduce the needle by the
tensile stress, increase their service life, while helping to squeeze from the hollow
material after the exit,sanitary ware fittings the hollow needle of the taper should be
based on material thickness negative deviation limit. General Extruder pin hole on the
work of some 550 ~ 600mrn length of the taper to make 0.5 ~ 0.6mm. This taper is not too
large, otherwise it will lead to changes in the size extrusion products.
Section size from the hollow needle piercing the hole size to determine material, needle
length equal to the work part of the Ingot length, spacer thickness, length and mode of
work with a piercing needle sanitary ware fittings out of work and with the length.
Bottle piercing needle structure in two parts: the needle and the needle sizing part
of the body, when the squeeze in the hole is less than 20 ~ 30mm thick-walled tube,
column piercing needle vertical perforation due to bending and heat, will piercing
billets incorrect or pulled fine, pull off, this case can be bottle piercing needle.
Extruded aluminum alloy, the surface of the column is often squeezed needle scratch pad,
affecting the surface quality, so it is with a bottle needle. But the diameter of the
needle and the needle body can not be too bad, depending on pipe diameter needle
diameter, the general diameter of the needle body 50 ~ 60mm or more thick, needle and
needle cone angle of the transition body 30 º ~ 50 º, the difference between the diameter
of the needle length is 0.2 ~ 0.3mm. Typically, the needle of assembly-type as well, but
the high temperature alloy extrusion with the overall style is appropriate, because the
high temperature deformation fabricated difficult to remove the thread.
Perforated by a needle the diameter of the inner diameter of the pipe to determine
the needle length equal to the sizing part of the model with the length of the work, with
the length of the work out mode and the margin of and. This allowance can not exceed more
than the thickness of pressure, usually 20 ~ 30mm, so as not to squeeze the hollow metal
rod in the back of people. Working out with a long needle desirable l0mm, so the holes on
the mold from the guide tube to prevent the elbow.
Piercing needle or a needle, whether bottle-pin column, which connecting rod with the
needle seat general use fine thread, the drawback is slow and difficult working needle,
and advanced mechanical handling extruder is used.
Permalink: http://www.cncasting-
forging.com/blog/1396.html
parts Extrusion bronze casting on sale
and to identify products within Brass forging the perforation hole size tool. Perforated
pipe inner surface of the needle in the quality assurance plays a decisive role. Needle
piercing the general circular cross-section for the production of pipe, pipe, and
gradually shaped cross section profiles. Piercing needle structure and brass forging
extrusion methods of operation and selection of product requirements.
Column part perforated cylindrical needle work, and its cross section round, shaped
and so on. Needle along the needle axis of column has a small taper, in the extrusion
process, the stationary perforated needle,sanitary
ware fittings only the front end with a tapered needle; and follower wearPin hole,
you need the entire length of the work of a very small taper to reduce the needle by the
tensile stress, increase their service life, while helping to squeeze from the hollow
material after the exit,sanitary ware fittings the hollow needle of the taper should be
based on material thickness negative deviation limit. General Extruder pin hole on the
work of some 550 ~ 600mrn length of the taper to make 0.5 ~ 0.6mm. This taper is not too
large, otherwise it will lead to changes in the size extrusion products.
Section size from the hollow needle piercing the hole size to determine material, needle
length equal to the work part of the Ingot length, spacer thickness, length and mode of
work with a piercing needle sanitary ware fittings out of work and with the length.
Bottle piercing needle structure in two parts: the needle and the needle sizing part
of the body, when the squeeze in the hole is less than 20 ~ 30mm thick-walled tube,
column piercing needle vertical perforation due to bending and heat, will piercing
billets incorrect or pulled fine, pull off, this case can be bottle piercing needle.
Extruded aluminum alloy, the surface of the column is often squeezed needle scratch pad,
affecting the surface quality, so it is with a bottle needle. But the diameter of the
needle and the needle body can not be too bad, depending on pipe diameter needle
diameter, the general diameter of the needle body 50 ~ 60mm or more thick, needle and
needle cone angle of the transition body 30 º ~ 50 º, the difference between the diameter
of the needle length is 0.2 ~ 0.3mm. Typically, the needle of assembly-type as well, but
the high temperature alloy extrusion with the overall style is appropriate, because the
high temperature deformation fabricated difficult to remove the thread.
Perforated by a needle the diameter of the inner diameter of the pipe to determine
the needle length equal to the sizing part of the model with the length of the work, with
the length of the work out mode and the margin of and. This allowance can not exceed more
than the thickness of pressure, usually 20 ~ 30mm, so as not to squeeze the hollow metal
rod in the back of people. Working out with a long needle desirable l0mm, so the holes on
the mold from the guide tube to prevent the elbow.
Piercing needle or a needle, whether bottle-pin column, which connecting rod with the
needle seat general use fine thread, the drawback is slow and difficult working needle,
and advanced mechanical handling extruder is used.
Permalink: http://www.cncasting-
forging.com/blog/1396.html
whsfe- New Member
-
Number of posts : 5
Age : 43
Registration date : 2010-11-15
To Improve Your Putting
To Improve Your Putting
Learning how to putt well can be a difficult challenge for many new players as they do not understand what it really takes to become good at this part of the game. The first step is to pick a certain mechanical approach to putting. discount golf clubs It is important to understand that there are many potential putting strokes that can work well for you so do not think that there is a magical putting style that will allow you to make every putt as even the best Ishiner putters 3 putt on occasion.
Learning how to putt well can be a difficult challenge for many new players as they do not understand what it really takes to become good at this part of the game. The first step is to pick a certain mechanical approach to putting. discount golf clubs It is important to understand that there are many potential putting strokes that can work well for you so do not think that there is a magical putting style that will allow you to make every putt as even the best Ishiner putters 3 putt on occasion.
ufoxx300- New Member
-
Number of posts : 3
Age : 36
Registration date : 2010-11-23
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum